www.avenview.com 1 8X8 HDMI 1.3 over CAT5 Matrix Switch with IR Pass-Through and 3D Support Model #: SW-HDM3D-C5-8X8
www.avenview.com 10 1.7.4 SW Main Dip Switch for Firmware Update DIP Switch Position PIN # 1 PIN # 2 PIN # 3 PIN # 4 Normal Operation Mode6 RS232 OF
www.avenview.com 11 1.8 IR Control Patch IR Blaster Cable IR Receiver Cable Incorrect placement of IR Blaster and Receiver may result
www.avenview.com 12 1.8.1 Supported IR Data Formats Data Format Suitable Not Recommended NEC RC5 TOSHIBA MICOM CODE GRUNDIG CODE SONY 12
www.avenview.com 13 1.9 Installation (SW-HDM3D-C5-8X8) To setup Avenview SW-HDM3D-C5-8X8 follow these steps for connecting to a device: Matrix Swi
www.avenview.com 14 1.10 Operation and IR Control 1.10.1 Source Side 1.10.1.1Method A: Push Button 1. Use the “” or “—“ channel button on output p
www.avenview.com 15 1.10.2 Display Side 1.10.2.1Method A: Push Button Press the INPUT SELECT push button to switch the input source on the respective
www.avenview.com 16 1.11 RS232 Serial Port Control Scan: Press Scan button, the machine will scan the all com port and show them. Select the RS232
www.avenview.com 17 Setting: Press Get button to read back device ID. Press Set button to write device ID. Linkage: Press Linkage button to read
www.avenview.com 18 Fast Select Button: Press Fast select button. Quick setting. Input one Output Port one Input two Output Port two ….. Press
www.avenview.com 19 1.11.1RS232 Commands COMMAND ACTION COMMAND ACTION COMMAND ACTION ST System Status* C5 Output C select Input5 F3 Output F sel
www.avenview.com 2 Table of Contents Section 1: Getting Started ...
www.avenview.com 20 Section 2: Specifications Item Description Units SW-HDM3D-C5-8X8 HDM3D-C5SW-R Unit Description 8X8 HDMI Matrix Switch over CAT5 w
www.avenview.com 21 2.1 EDID Learning The EDID learning function is only necessary whenever you encounter any display on the HDMI output port th
www.avenview.com 22 2.2 Method 2: Use the Front Panel of The Master Unit Button Function Output Port EDID will be read from display via the connecte
www.avenview.com 23 2.2 IR Discrete Code Default Custom Code - IR2 Code: 00 FF Function 0x17 0x0A 0x0C POWER 0x02 SOURCE SEL. 1 0x54 SOURCE SEL.
www.avenview.com 24 Custom Code - IR3 Code: 0x12 0x21 Custom Code: 0x12 0x21 Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8
www.avenview.com 25 Command Custom Code IR2 0x00 0xFF IR3 0x12 0x21 IR4 0x13 0x31
www.avenview.com 26 Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liabili
www.avenview.com 3 Section 1: Getting Started 1.1 Important Safeguards Please read all of these instructions carefully before you use the device. Sa
www.avenview.com 4 1.3 Regulatory Notices Federal Communications Commission (FCC) This equipment has been tested and found to comply with Part 15 o
www.avenview.com 5
www.avenview.com 6 - Supports HDMI Deep Color & Full 3D - Re-clocking TMDS single - HDCP compliant - Allows any source to be displayed on mul
www.avenview.com 7 1.7 Panel Description 1.7.1 SW-HDM3D-C5-8X8 Front Panel 1 2 3 4 5 1. Power: Power Co
www.avenview.com 8 1.7.3 HDM3D-C5SW-R 1. IR Receiver: Plug in IR receiver 2. 5V DC Power jack 3. HDMI Signal Input: Plug in CAT 5/6 4.
www.avenview.com 9 1.7.3 Dip Switch for EDID & Audio Settings (SW1 – SW8) DIP Switch Position Video Audio Description PIN # 1 PIN # 2 OFF OFF
Commentaires sur ces manuels